We recommend testing the cut each time you put new This button will send a 1 triangle in a square testĬoupon to the cutter. Setto set up function, can change XP/YP, Tool offset, sensitivity. LCD screento display function and error messages. The blade holder will sit in the carriage on the right side of the blade holder,Īnd is secured to the carriage using the thumbscrew in the front. The blade should not cut through the substrate as it will Setup for cutting you will need to adjust the cutting force so that the blade fullyĬuts through the vinyl layer and partially cuts through the substrate (or carrier Recommend starting with an exposure distance of about 1/32 (approximately As such, theīlade doesnt need to be exposed from the blade holder shield very much. Of the blade (only the very tip is used in cutting thin materials). 002-.005 thick which only uses a very small amount It is important for good quality vinyl cutting to achieve the correct blade depth Press the push-pin to remove the blade form the blade holder when replacing blade. Nut and rotating the blade holder shield and Unlocking (rotate counter clockwise) the lock Adjust the blade tip to suitable length by Push the blade to the bottom of the blade The blade will not cut cleanly even though the blade force has been raisedġ. The cutting traces are not as good as they were when the blade was new.ģ. The blade is a consumable item and you will always getĢ.
Secure the machine to the stand using the nuts thatĭont touch the tip of the blade with your fingers.
Placing the cutter on the stand and aligning the four bolts with the slots in the Insert the bolts from the bottom of the machine to the top of floor stand by Remove the four nuts from the bottom of the machine mounting bolts and Installing the floor stand to the machine. Step4 Place two roll holders into the holes in the roll holder support. Position the roll holder supports to floor stand as shown below, and tighten screws. The holes, but dont tighten them at this step. Place the stand beam upright on the T-stand and put the screws into Repeat the same steps with the support for the right side Position the support for the left side perpendicularly to the bottom stand and place the screws into the holes. Please check immediately to ensure that you have received the followingĬutting plotter stand (dismantled and in the bottom of the box) Manually moving the carriage can induceĬurrents from the motor into the motherboard, overload the electronics and During severe weather, unplug the machine.ĭo not use your hands to manually move the carriage, use the controlīuttons in off-line mode instead. Never run the machine during a thunder storm as lighting could damage orĭestroy the machine. Set up the machine on a stable base to avoid danger of falling. Machine parts unattended when plugged-in.ĭo not touch the tips of the cutting blade to avoid injury and damage to the Keep the cutting plotter away from children, and never leave the machine or Keep your hands well away from the blade holder while the carriage isĬancel the active job or preferably, power down the cutter before adjusting Unplug the power lead during long periods of inactivity. In case of extreme main power fluctuations, use a voltage Insure that the main power supply220V/110V) doesnt fluctuate by more Should be electrically connected to the vinyl cutter.
Grounding is very important for proper cutter function. Do not bypass the ground lead for theĬutter. Without instructed to do so by a Saga technician.Īvoid liquid spills and metal objects from entering the interior of the cutter. Never open the machine case and dont attempt to modify the machine Keep your hands or other parts of the body far from the carriage when using Levers up on the back side of the cutter. Release the pressure contact rollers when not in use by flipping the pressure Running as this may cause damage to plotter. Pressure and possibly damage the carriage mechanism.ĭont unplug the connection to the computer lead line when the plotter is Please read these instructions and precautionary notes carefully before usingĭont place magnetic objects near the cutting head as it will affect cutting We do not assume any liabilityįor direct or indirect damage that occurs due to the use of this product. Plotter for production use in a few easy steps. For all comments, queries or suggestions concerning
#Saga cutting plotter driver download manual#
Manual at any time without prior noticeun-authorized modification, copying orĭistribution is prohibited. We reserve the right to modify the information contained in this user
Hefei Saga Computer Numerical Control CO.,LTDĬongratulations on purchasing a Saga cutting plotter!
0 kommentar(er)
